Navcom StarUtil Rev.E Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Zařízení Navcom StarUtil Rev.E. NavCom StarUtil Rev.E User Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk

Shrnutí obsahu

Strany 1 - NavCom Technology, Inc

SSttaarrUUttiill UUsseerr GGuuiiddee NavCom Technology, Inc. 20780 Madrona Avenue Torrance, CA 90503 USA Tel: +1 310.381.2000 Fax: +1 310.381.20

Strany 2

STARUTIL User Guide Rev. E Chapter 2 Establishing Communications & Control In order to execute StarUtil double click on the icon. Once StarUtil

Strany 3 - Table of Contents

STARUTIL User Guide Rev. E Now that PC Port Configuration has been established, the receiver must have its logical ports setup to meet the spec

Strany 4

STARUTIL User Guide Rev. E Chapter 3 Navigation & Data Output Configuration At this point the GPS receiver is ready to be configured for your s

Strany 5 - Table of Figures

STARUTIL User Guide Rev. E The user is allowed to add or delete NCT and/or NMEA message from each format’s output list. This is established by

Strany 6

STARUTIL User Guide Rev. E There are two check boxes that allow the end user to quickly delete all messages in the NCT-2100/NCT-2000 Message List. By

Strany 7 - Notices

STARUTIL User Guide Rev. E Figure 10: NCT Message Output Rate Choice The NCT messages scheduled should appear scrolling up in the Mess

Strany 8 - Chapter 1 Introduction

STARUTIL User Guide Rev. E Solid Earth Tide (SET) Implementation In order to have the SET correction information applied to the position solution ther

Strany 9 - Initiating Data Logging

STARUTIL User Guide Rev. E The Set Receiver Position screen will appear as shown in Figure 14. The Receiver Position Menu is comprised of Messa

Strany 10

STARUTIL User Guide Rev. E Figure 15: Rover Navigation & Tracking Parameters Setup The Navigation Elevation Mask selects the elevation

Strany 11 - receiver for the

STARUTIL User Guide Rev. E the receiver will transition from a 2D [3 satellite] to a 3D [4 satellite] navigation mode automatically, and use th

Strany 13

STARUTIL User Guide Rev. E The Tracking Elevation Mask selects the elevation angle the receiver starts tracking satellites. The default is set to 0 d

Strany 14

STARUTIL User Guide Rev. E Figure 18: View of Tabbed NCT Messages in ASCII Figure 19: View of Tabbed 0xB1 in

Strany 15

STARUTIL User Guide Rev. E Once the receiver is setup and tracking satellites, the signal characteristics of the satellites being tracked can be viewe

Strany 16

STARUTIL User Guide Rev. E 7. SV: The GPS satellite number assigned to that particular channel. State: The NCT proprietary satellite tracking v

Strany 17

STARUTIL User Guide Rev. E Chapter 4 Base Station Setup Throughout the first three chapters, your receiver has been navigating as an autonomous stat

Strany 18

STARUTIL User Guide Rev. E Figure 22 shows the window that will appear. The Network ID can be set to any value as low as 1 and as high as 65535

Strany 19

STARUTIL User Guide Rev. E In the Define Correction Type area of Figure 23, you will choose the corrections that are required for output, the Correcti

Strany 20

STARUTIL User Guide Rev. E Since in this example we are taking advantage of the on board radio, we need to setup the power output, and set up t

Strany 21

STARUTIL User Guide Rev. E Figure 29: Radio Configuration; Power Level Now that the unit is configured to output the corrections, the output

Strany 22

STARUTIL User Guide Rev. E Press the Base Icon on the StarUtil main window, and Figure 23 will appear. This is the Base Configuration window, w

Strany 23

STARUTIL User Guide Rev. E Table of Contents Table of Contents...

Strany 24 - equipped receiver

STARUTIL User Guide Rev. E Chapter 5 RTK Extend / RTK / dGPS / SBAS Rover Setup Depending on the options you have purchased, the receiver can use an

Strany 25

STARUTIL User Guide Rev. E Base & Rover pair for optimal performance, and also requires an external RTK link be established. RTK Extend is

Strany 26

STARUTIL User Guide Rev. E Go to the Rover Navigation & Tracking window shown in Figure 15; in the dGPS Corrections area click the “USE” button ad

Strany 27

STARUTIL User Guide Rev. E Chapter 6 NMEA Setup and Output The receiver has the ability to output 9 industry standard NMEA data strings, and 1 N

Strany 28

STARUTIL User Guide Rev. E NMEA can be logged and/or viewed using the NMEA Viewer window, although any ASCII RS232 port viewer will suffice. This a

Strany 29

STARUTIL User Guide Rev. E NMEA GGA Station ID Field 14 The NMEA GGA message field 14 is now user configurable and can display information that st

Strany 30 - NCT RTK Extend Input

STARUTIL User Guide Rev. E Chapter 7 Data Logging Data can be logged from either of the physical ports, or to the on board 64 Megabyte Memory Module

Strany 31 - CMR+/CMR RTK Input

STARUTIL User Guide Rev. E The Current Status area lets the user know if logging is enabled, if the scheduler [24-hour splits] is enabled, an

Strany 32 - WAAS/EGNOS

STARUTIL User Guide Rev. E Once the messages have been scheduled to the Log Port, open up the MMC window by going to the main StarUtil menu and clicki

Strany 33

STARUTIL User Guide Rev. E If you have never used the internal logging feature, the MMC must be formatted. Click on the More button shown in Figur

Strany 34

STARUTIL User Guide Rev. E Get Ephemeris...

Strany 35 - NMEA GGA Station ID Field 14

STARUTIL User Guide Rev. E Enter the logging filename in MS-DOS 8.3 format. Once logging has begun, the Start Internal Logging button shown in Figure

Strany 36 - Chapter 7 Data Logging

STARUTIL User Guide Rev. E Chapter 8 StarFire Specific Operation There are several StarUtil menu options that are specific only to StarFire™

Strany 37 - Internal NCT Binary Logging

STARUTIL User Guide Rev. E Alternate Channel & StarFire™ Frequencies Figure 50 allows the end use to assign an alternate StarFire™ frequency for r

Strany 38

STARUTIL User Guide Rev. E Table 2: StarFire™ Channel Numbers and Satellites The Tracked Baseband Frequency should be a value between -

Strany 39 - Figure 44: MMC Format Label

STARUTIL User Guide Rev. E successful completion or proximity failure, this request will return the reported QuickStart mode to ‘Idle’. c. A

Strany 40

STARUTIL User Guide Rev. E StarFire License Installation Using StarUtil The StarFire Network is a subscriber service, and each StarFire equippe

Strany 41 - Configure LBM Message Output

STARUTIL User Guide Rev. E Chapter 9 1PPS/Events The 1 PPS output pulse output from the receiver is synchronized with GPS time, and is shaped as des

Strany 42

STARUTIL User Guide Rev. E Figure 57: Event Latch Output Rate Configuration  Please refer to the Product’s User Guide for hardware

Strany 43 - INMARSAT ASPAC 41090

STARUTIL User Guide Rev. E Chapter 10 Ack/Nacks & General Commands This section details fundamental response sent back from the unit whenever a

Strany 44

STARUTIL User Guide Rev. E General Duty Commands Here is where almanac is downloaded, and uploaded from/to the receiver. This is a great benefit whe

Strany 45

STARUTIL User Guide Rev. E Table of Figures Figure 1: StarUtil Toolbar...

Strany 46 - Chapter 9 1PPS/Events

STARUTIL User Guide Rev. E Chapter 11 Tools Menu The Tools menu is an area of StarUtil where the user will upload new firmware, StarFire™ licenses,

Strany 47

STARUTIL User Guide Rev. E Save System Configuration This feature allows the user’s system configuration information to be written to a text file. Cl

Strany 48 - Ack/Nack

STARUTIL User Guide Rev. E MSG ID DISCRIPTION 1A Port Configuration Block 20 Data Request 30 Software Options 49 Solution Control AE Identificati

Strany 49

STARUTIL User Guide Rev. E Figure 65: Options File Opened In NotePad At the bottom of the file text there will be a 24 character Options

Strany 50 - Chapter 11 Tools Menu

STARUTIL User Guide Rev. E Load Software Although there is a separate utility designed specifically to update the various software modules in the N

Strany 51 - Save System Configuration

STARUTIL User Guide Rev. E The next window you see will be Figure 70 stating that the software upload has been successful. This process must be repeat

Strany 52 - Load Software Options

STARUTIL User Guide Rev. E Appendix A NCT Solid Earth Tide (SET) Message Format The SET message output via the NMEA port is a NavCom proprietary NMEA

Strany 53

STARUTIL User Guide Rev. E Appendix B NCT Station ID NMEA GGA Field 14 Definitions Tables B1 & B2 detail the information contained in field 14 of

Strany 54 - Load Software

STARUTIL User Guide Rev. E ID (YY) GPS CORRECTION SIGNAL 00 Non dGPS 01 dGPS, RTCM type 1 or 9, Single Freq 02 WAAS/EGNOS, Single Freq., (See GSA f

Strany 55

STARUTIL User Guide Rev. E Figure 60: Tools Commands ...

Strany 56

STARUTIL User Guide Rev. E Notices StarUtil Engineering Program User Guide P/N 96-310008-3001 Revision E July 2005 Co

Strany 57

STARUTIL User Guide Rev. E Chapter 1 Introduction StarUtil Overview StarUtil is designed for use as an Engineering/OEM application. This utility is

Strany 58

STARUTIL User Guide Rev. E they may access additional menu screens that allow setup of such items as the internal radio, or L-Band Module. Rece

Příbuzné modely NCT-2050M Rev.D | StarUtil Rev.D | StarUtil Rev.C |

Komentáře k této Příručce

Žádné komentáře